Enable the AutoRemover to talk "Multi-Arch" by marking all pseudo

[apt.git] / dselect / install

diff --git a/dselect/install b/dselect/install
index 6cf5dcf1addc61f0ae3aa5650b74187656d6260c..6779698e0ab817591a6aa1f4c20b6642e008e33d 100755 (executable)
--- a/dselect/install
+++ b/dselect/install
@@ -1,14 +1,22 @@
-#!/bin/sh
+#!/bin/bash
+
+# Set the textdomain for the translations using $"..."
+TEXTDOMAIN="apt"
 
 # Get the configuration from /etc/apt/apt.conf
 CLEAN="prompt"
 OPTS="-f"
 APTGET="/usr/bin/apt-get"
 DPKG="/usr/bin/dpkg"
+DPKG_OPTS="--admindir=$1"
+APT_OPT0="-oDir::State::status=$1/status"
+APT_OPT1="-oDPkg::Options::=$DPKG_OPTS"
 set -e
 RES=`apt-config shell CLEAN DSelect::Clean OPTS DSelect::Options \
-                      DPKG Dir::Bin::dpkg/ APTGET Dir::Bin::apt-get/ \
-                     ARCHIVES Dir::Cache::Archives/`
+                      DPKG Dir::Bin::dpkg/f APTGET Dir::Bin::apt-get/f \
+                     ARCHIVES Dir::Cache::Archives/d \
+                     WAIT DSelect::WaitAfterDownload/b \
+                     CHECKDIR DSelect::CheckDir/b`
 eval $RES
 set +e
 
@@ -19,15 +27,15 @@ yesno() {
        local ans def defp
        if [ "$2" ];then
                case $2 in
-                       Y|y)    defp="(Y/n)" def=y;;
-                       N|n)    defp="(y/N)" def=n;;
-                       *)      echo "Bad default setting!" 1>&2; exit 1;;
+                       Y|y)    defp="[Y/n]" def=y;;
+                       N|n)    defp="[y/N]" def=n;;
+                       *)      echo $"Bad default setting!" 1>&2; exit 1;;
                esac
        else
-               defp="(y/N)" def=n
+               defp="[y/N]" def=n
        fi
        while :;do
-               echo -n "$1$defp" 1>&3
+               echo -n "$1 $defp " 1>&3
                read ans
                case $ans in
                        Y|y|N|n)        break;;
@@ -38,8 +46,15 @@ yesno() {
        echo $ans | tr YN yn
 }
 
-$APTGET $OPTS dselect-upgrade
-RES=$?
+if [ x$WAIT = "xtrue" ]; then
+   $APTGET $OPTS "$APT_OPT0" "$APT_OPT1" -d dselect-upgrade
+   echo $"Press enter to continue." && read RES
+   $APTGET $OPTS "$APT_OPT0" "$APT_OPT1" dselect-upgrade
+   RES=$?
+else
+   $APTGET $OPTS "$APT_OPT0" "$APT_OPT1" dselect-upgrade
+   RES=$?
+fi
 
 # 1 means the user choose no at the prompt
 if [ $RES -eq 1 ]; then
@@ -53,31 +68,42 @@ if [ $RES -eq 0 ]; then
         -eq 0 ]; then
       exit 0
    fi
+
+   NEWLS=`ls -ld $ARCHIVES`
+   if [ x$CHECKDIR = "xtrue" ]; then
+      if [ "x$OLDLS" = "x$NEWLS" ]; then
+         exit 0
+      fi
+   fi
    
    # Check the cleaning mode
    case `echo $CLEAN | tr '[:upper:]' '[:lower:]'` in
      auto)
-       $APTGET autoclean && echo "Press enter to continue." && read RES && exit 0;
+       $APTGET "$APT_OPT0" "$APT_OPT1" autoclean &&
+          echo $"Press enter to continue." && read RES && exit 0;
        ;;
      always)
-       $APTGET clean && echo "Press enter to continue." && read RES && exit 0;
+       $APTGET "$APT_OPT0" "$APT_OPT1" clean &&
+          echo $"Press enter to continue." && read RES && exit 0;
        ;;
      prompt)
        exec 3>&1
-       if [ `yesno "Do you want to erase the downloaded .deb files " y` = y ]; then
-          $APTGET clean && echo "Press enter to continue." && read RES && exit 0;
+       echo -n $"Do you want to erase any previously downloaded .deb files?"
+       if [ `yesno "" y` = y ]; then
+          $APTGET "$APT_OPT0" "$APT_OPT1" clean &&
+           echo $"Press enter to continue." && read RES && exit 0;
        fi
        ;;
      *) 
        ;;
    esac   
 else
-   echo "Some errors occurred while unpacking. I'm going to configure the"
-   echo "packages that were installed. This may result in duplicate errors"
-   echo "or errors caused by missing dependencies. This is OK, only the errors"
-   echo "above this message are important. Please fix them and run [I]nstall again"
-   echo "Press enter to continue."
-   read RES && $DPKG --configure -a
+   echo $"Some errors occurred while unpacking. Packages that were installed"
+   echo $"will be configured. This may result in duplicate errors"
+   echo $"or errors caused by missing dependencies. This is OK, only the errors"
+   echo $"above this message are important. Please fix them and run [I]nstall again"
+   echo $"Press enter to continue."
+   read RES && $DPKG "$DPKG_OPTS" --configure -a
    exit 100
 fi