* Mark a message from dselect backend as translatable

[apt.git] / dselect / install

diff --git a/dselect/install b/dselect/install
index e543344b53337d485d3b6b40981b4fbc55300efc..61d13208e2f9c0d2fc1fa56036edd777d731c129 100755 (executable)
--- a/dselect/install
+++ b/dselect/install
@@ -1,15 +1,22 @@
-#!/bin/sh
+#!/bin/bash
+
+# Set the textdomain for the translations using $"..."
+TEXTDOMAIN="apt"
 
 # Get the configuration from /etc/apt/apt.conf
 CLEAN="prompt"
 OPTS="-f"
 APTGET="/usr/bin/apt-get"
 DPKG="/usr/bin/dpkg"
+DPKG_OPTS="--admindir=$1"
+APT_OPT0="-oDir::State::status=$1/status"
+APT_OPT1="-oDPkg::Options::=$DPKG_OPTS"
 set -e
 RES=`apt-config shell CLEAN DSelect::Clean OPTS DSelect::Options \
-                      DPKG Dir::Bin::dpkg APTGET Dir::Bin::apt-get \
-                     ARCHIVES Dir::Cache::Archives/ \
-                     WAIT DSelect::WaitAfterDownload`
+                      DPKG Dir::Bin::dpkg/f APTGET Dir::Bin::apt-get/f \
+                     ARCHIVES Dir::Cache::Archives/d \
+                     WAIT DSelect::WaitAfterDownload/b \
+                     CHECKDIR DSelect::CheckDir/b`
 eval $RES
 set +e
 
@@ -22,7 +29,7 @@ yesno() {
                case $2 in
                        Y|y)    defp="[Y/n]" def=y;;
                        N|n)    defp="[y/N]" def=n;;
-                       *)      echo "Bad default setting!" 1>&2; exit 1;;
+                       *)      echo $"Bad default setting!" 1>&2; exit 1;;
                esac
        else
                defp="[y/N]" def=n
@@ -39,13 +46,13 @@ yesno() {
        echo $ans | tr YN yn
 }
 
-if [ x$WAIT = "xyes" ]; then
-   $APTGET $OPTS -d dselect-upgrade
-   echo "Press enter to continue." && read RES
-   $APTGET $OPTS dselect-upgrade
+if [ x$WAIT = "xtrue" ]; then
+   $APTGET $OPTS "$APT_OPT0" "$APT_OPT1" -d dselect-upgrade
+   echo $"Press enter to continue." && read RES
+   $APTGET $OPTS "$APT_OPT0" "$APT_OPT1" dselect-upgrade
    RES=$?
 else
-   $APTGET $OPTS dselect-upgrade
+   $APTGET $OPTS "$APT_OPT0" "$APT_OPT1" dselect-upgrade
    RES=$?
 fi
 
@@ -62,30 +69,41 @@ if [ $RES -eq 0 ]; then
       exit 0
    fi
 
+   NEWLS=`ls -ld $ARCHIVES`
+   if [ x$CHECKDIR = "xtrue" ]; then
+      if [ "x$OLDLS" = "x$NEWLS" ]; then
+         exit 0
+      fi
+   fi
+   
    # Check the cleaning mode
    case `echo $CLEAN | tr '[:upper:]' '[:lower:]'` in
      auto)
-       $APTGET autoclean && echo "Press enter to continue." && read RES && exit 0;
+       $APTGET "$APT_OPT0" "$APT_OPT1" autoclean &&
+          echo $"Press enter to continue." && read RES && exit 0;
        ;;
      always)
-       $APTGET clean && echo "Press enter to continue." && read RES && exit 0;
+       $APTGET "$APT_OPT0" "$APT_OPT1" clean &&
+          echo $"Press enter to continue." && read RES && exit 0;
        ;;
      prompt)
        exec 3>&1
-       if [ `yesno "Do you want to erase any previously downloaded .deb files?" y` = y ]; then
-          $APTGET clean && echo "Press enter to continue." && read RES && exit 0;
+       echo -n $"Do you want to erase any previously downloaded .deb files?"
+       if [ `yesno "" y` = y ]; then
+          $APTGET "$APT_OPT0" "$APT_OPT1" clean &&
+           echo $"Press enter to continue." && read RES && exit 0;
        fi
        ;;
      *) 
        ;;
    esac   
 else
-   echo "Some errors occurred while unpacking. I'm going to configure the"
-   echo "packages that were installed. This may result in duplicate errors"
-   echo "or errors caused by missing dependencies. This is OK, only the errors"
-   echo "above this message are important. Please fix them and run [I]nstall again"
-   echo "Press enter to continue."
-   read RES && $DPKG --configure -a
+   echo $"Some errors occurred while unpacking. I'm going to configure the"
+   echo $"packages that were installed. This may result in duplicate errors"
+   echo $"or errors caused by missing dependencies. This is OK, only the errors"
+   echo $"above this message are important. Please fix them and run [I]nstall again"
+   echo $"Press enter to continue."
+   read RES && $DPKG "$DPKG_OPTS" --configure -a
    exit 100
 fi