Update with files from apt-sarge. Complete French translation.

[apt.git] / dselect / install

#!/bin/bash

# Set the textdomain for the translations using $"..."
TEXTDOMAIN="apt"

# Get the configuration from /etc/apt/apt.conf
CLEAN="prompt"
OPTS="-f"
APTGET="/usr/bin/apt-get"
DPKG="/usr/bin/dpkg"
DPKG_OPTS="--admindir=$1"
APT_OPT0="-oDir::State::status=$1/status"
APT_OPT1="-oDPkg::Options::=$DPKG_OPTS"
set -e
RES=`apt-config shell CLEAN DSelect::Clean OPTS DSelect::Options \
                      DPKG Dir::Bin::dpkg/f APTGET Dir::Bin::apt-get/f \
		      ARCHIVES Dir::Cache::Archives/d \
		      WAIT DSelect::WaitAfterDownload/b \
		      CHECKDIR DSelect::CheckDir/b`
eval $RES
set +e

# Yes/No Prompter
yesno() {
# $1 = prompt
# $2 = default(y)
	local ans def defp
	if [ "$2" ];then
		case $2 in
			Y|y)	defp="[Y/n]" def=y;;
			N|n)	defp="[y/N]" def=n;;
			*)	echo $"Bad default setting!" 1>&2; exit 1;;
		esac
	else
		defp="[y/N]" def=n
	fi
	while :;do
		echo -n "$1 $defp " 1>&3
		read ans
		case $ans in
			Y|y|N|n)	break;;
			"")		ans=$def;break;;
		esac
		echo
	done
	echo $ans | tr YN yn
}

if [ x$WAIT = "xtrue" ]; then
   $APTGET $OPTS "$APT_OPT0" "$APT_OPT1" -d dselect-upgrade
   echo $"Press enter to continue." && read RES
   $APTGET $OPTS "$APT_OPT0" "$APT_OPT1" dselect-upgrade
   RES=$?
else
   $APTGET $OPTS "$APT_OPT0" "$APT_OPT1" dselect-upgrade
   RES=$?
fi

# 1 means the user choose no at the prompt
if [ $RES -eq 1 ]; then
  exit 0
fi

# Finished OK
if [ $RES -eq 0 ]; then

   if [ `ls $ARCHIVES $ARCHIVES/partial | egrep -v "^lock$|^partial$" | wc -l` \
        -eq 0 ]; then
      exit 0
   fi

   NEWLS=`ls -ld $ARCHIVES`
   if [ x$CHECKDIR = "xtrue" ]; then
      if [ "x$OLDLS" = "x$NEWLS" ]; then
         exit 0
      fi
   fi
   
   # Check the cleaning mode
   case `echo $CLEAN | tr '[:upper:]' '[:lower:]'` in
     auto)
       $APTGET "$APT_OPT0" "$APT_OPT1" autoclean &&
	   echo $"Press enter to continue." && read RES && exit 0;
       ;;
     always)
       $APTGET "$APT_OPT0" "$APT_OPT1" clean &&
	   echo $"Press enter to continue." && read RES && exit 0;
       ;;
     prompt)
       exec 3>&1
       if [ `yesno $"Do you want to erase any previously downloaded .deb files?" y` = y ]; then
          $APTGET "$APT_OPT0" "$APT_OPT1" clean &&
	    echo $"Press enter to continue." && read RES && exit 0;
       fi
       ;;
     *) 
       ;;
   esac   
else
   echo $"Some errors occurred while unpacking. I'm going to configure the"
   echo $"packages that were installed. This may result in duplicate errors"
   echo $"or errors caused by missing dependencies. This is OK, only the errors"
   echo $"above this message are important. Please fix them and run [I]nstall again"
   echo $"Press enter to continue."
   read RES && $DPKG "$DPKG_OPTS" --configure -a
   exit 100
fi

exit $?