pidfile /var/run/redis.pid
# Accept connections on the specified port, default is 6379.
+# If port 0 is specified Redis will not listen on a TCP socket.
port 6379
# If you want you can bind a single interface, if the bind option is not
# on a unix socket when not specified.
#
# unixsocket /tmp/redis.sock
+# unixsocketperm 755
# Close the connection after a client is idle for N seconds (0 to disable)
-timeout 300
+timeout 0
# Set server verbosity to 'debug'
# it can be one of:
# verbose (many rarely useful info, but not a mess like the debug level)
# notice (moderately verbose, what you want in production probably)
# warning (only very important / critical messages are logged)
-loglevel verbose
+loglevel notice
# Specify the log file name. Also 'stdout' can be used to force
# Redis to log on the standard output. Note that if you use standard
# is still in progress, the slave can act in two different ways:
#
# 1) if slave-serve-stale-data is set to 'yes' (the default) the slave will
-# still reply to client requests, possibly with out of data data, or the
+# still reply to client requests, possibly with out of date data, or the
# data set may just be empty if this is the first synchronization.
#
# 2) if slave-serve-stale data is set to 'no' the slave will reply with
#
slave-serve-stale-data yes
+# Slaves send PINGs to server in a predefined interval. It's possible to change
+# this interval with the repl_ping_slave_period option. The default value is 10
+# seconds.
+#
+# repl-ping-slave-period 10
+
+# The following option sets a timeout for both Bulk transfer I/O timeout and
+# master data or ping response timeout. The default value is 60 seconds.
+#
+# It is important to make sure that this value is greater than the value
+# specified for repl-ping-slave-period otherwise a timeout will be detected
+# every time there is low traffic between the master and the slave.
+#
+# repl-timeout 60
+
################################## SECURITY ###################################
# Require clients to issue AUTH <PASSWORD> before processing any other
################################### LIMITS ####################################
-# Set the max number of connected clients at the same time. By default there
-# is no limit, and it's up to the number of file descriptors the Redis process
-# is able to open. The special value '0' means no limits.
+# Set the max number of connected clients at the same time. By default
+# this limit is set to 10000 clients, however if the Redis server is not
+# able ot configure the process file limit to allow for the specified limit
+# the max number of allowed clients is set to the current file limit
+# minus 32 (as Redis reserves a few file descriptors for internal uses).
+#
# Once the limit is reached Redis will close all the new connections sending
# an error 'max number of clients reached'.
#
-# maxclients 128
+# maxclients 10000
# Don't use more memory than the specified amount of bytes.
# When the memory limit is reached Redis will try to remove keys with an
# "no" that is the safest pick from the point of view of durability.
no-appendfsync-on-rewrite no
-################################ VIRTUAL MEMORY ###############################
-
-# Virtual Memory allows Redis to work with datasets bigger than the actual
-# amount of RAM needed to hold the whole dataset in memory.
-# In order to do so very used keys are taken in memory while the other keys
-# are swapped into a swap file, similarly to what operating systems do
-# with memory pages.
+# Automatic rewrite of the append only file.
+# Redis is able to automatically rewrite the log file implicitly calling
+# BGREWRITEAOF when the AOF log size will growth by the specified percentage.
+#
+# This is how it works: Redis remembers the size of the AOF file after the
+# latest rewrite (or if no rewrite happened since the restart, the size of
+# the AOF at startup is used).
+#
+# This base size is compared to the current size. If the current size is
+# bigger than the specified percentage, the rewrite is triggered. Also
+# you need to specify a minimal size for the AOF file to be rewritten, this
+# is useful to avoid rewriting the AOF file even if the percentage increase
+# is reached but it is still pretty small.
#
-# To enable VM just set 'vm-enabled' to yes, and set the following three
-# VM parameters accordingly to your needs.
+# Specify a precentage of zero in order to disable the automatic AOF
+# rewrite feature.
-vm-enabled no
-# vm-enabled yes
+auto-aof-rewrite-percentage 100
+auto-aof-rewrite-min-size 64mb
-# This is the path of the Redis swap file. As you can guess, swap files
-# can't be shared by different Redis instances, so make sure to use a swap
-# file for every redis process you are running. Redis will complain if the
-# swap file is already in use.
-#
-# The best kind of storage for the Redis swap file (that's accessed at random)
-# is a Solid State Disk (SSD).
-#
-# *** WARNING *** if you are using a shared hosting the default of putting
-# the swap file under /tmp is not secure. Create a dir with access granted
-# only to Redis user and configure Redis to create the swap file there.
-vm-swap-file /tmp/redis.swap
+################################ LUA SCRIPTING ###############################
-# vm-max-memory configures the VM to use at max the specified amount of
-# RAM. Everything that deos not fit will be swapped on disk *if* possible, that
-# is, if there is still enough contiguous space in the swap file.
+# Max execution time of a Lua script in milliseconds.
#
-# With vm-max-memory 0 the system will swap everything it can. Not a good
-# default, just specify the max amount of RAM you can in bytes, but it's
-# better to leave some margin. For instance specify an amount of RAM
-# that's more or less between 60 and 80% of your free RAM.
-vm-max-memory 0
-
-# Redis swap files is split into pages. An object can be saved using multiple
-# contiguous pages, but pages can't be shared between different objects.
-# So if your page is too big, small objects swapped out on disk will waste
-# a lot of space. If you page is too small, there is less space in the swap
-# file (assuming you configured the same number of total swap file pages).
+# If the maximum execution time is reached Redis will log that a script is
+# still in execution after the maxium allowed time and will start to
+# reply to queries with an error.
#
-# If you use a lot of small objects, use a page size of 64 or 32 bytes.
-# If you use a lot of big objects, use a bigger page size.
-# If unsure, use the default :)
-vm-page-size 32
-
-# Number of total memory pages in the swap file.
-# Given that the page table (a bitmap of free/used pages) is taken in memory,
-# every 8 pages on disk will consume 1 byte of RAM.
+# When a long running script exceed the maxium execution time only the
+# SCRIPT KILL and SHUTDOWN NOSAVE commands are available. The first can be
+# used to stop a script that did not yet called write commands. The second
+# is the only way to shut down the server in the case a write commands was
+# already issue by the script but the user don't want to wait for the natural
+# termination of the script.
#
-# The total swap size is vm-page-size * vm-pages
+# Set it to 0 or a negative value for unlimited execution without warnings.
+lua-time-limit 5000
+
+################################ REDIS CLUSTER ###############################
#
-# With the default of 32-bytes memory pages and 134217728 pages Redis will
-# use a 4 GB swap file, that will use 16 MB of RAM for the page table.
+# Normal Redis instances can't be part of a Redis Cluster, only nodes that are
+# started as cluster nodes can. In order to start a Redis instance as a
+# cluster node enable the cluster support uncommenting the following:
#
-# It's better to use the smallest acceptable value for your application,
-# but the default is large in order to work in most conditions.
-vm-pages 134217728
+# cluster-enabled yes
-# Max number of VM I/O threads running at the same time.
-# This threads are used to read/write data from/to swap file, since they
-# also encode and decode objects from disk to memory or the reverse, a bigger
-# number of threads can help with big objects even if they can't help with
-# I/O itself as the physical device may not be able to couple with many
-# reads/writes operations at the same time.
+# Every cluster node has a cluster configuration file. This file is not
+# intended to be edited by hand. It is created and updated by Redis nodes.
+# Every Redis Cluster node requires a different cluster configuration file.
+# Make sure that instances running in the same system does not have
+# overlapping cluster configuration file names.
#
-# The special value of 0 turn off threaded I/O and enables the blocking
-# Virtual Memory implementation.
-vm-max-threads 4
+# cluster-config-file nodes-6379.conf
-############################### ADVANCED CONFIG ###############################
+# In order to setup your cluster make sure to read the documentation
+# available at http://redis.io web site.
+
+################################## SLOW LOG ###################################
-# Glue small output buffers together in order to send small replies in a
-# single TCP packet. Uses a bit more CPU but most of the times it is a win
-# in terms of number of queries per second. Use 'yes' if unsure.
-glueoutputbuf yes
+# The Redis Slow Log is a system to log queries that exceeded a specified
+# execution time. The execution time does not include the I/O operations
+# like talking with the client, sending the reply and so forth,
+# but just the time needed to actually execute the command (this is the only
+# stage of command execution where the thread is blocked and can not serve
+# other requests in the meantime).
+#
+# You can configure the slow log with two parameters: one tells Redis
+# what is the execution time, in microseconds, to exceed in order for the
+# command to get logged, and the other parameter is the length of the
+# slow log. When a new command is logged the oldest one is removed from the
+# queue of logged commands.
+
+# The following time is expressed in microseconds, so 1000000 is equivalent
+# to one second. Note that a negative number disables the slow log, while
+# a value of zero forces the logging of every command.
+slowlog-log-slower-than 10000
+
+# There is no limit to this length. Just be aware that it will consume memory.
+# You can reclaim memory used by the slow log with SLOWLOG RESET.
+slowlog-max-len 1024
+
+############################### ADVANCED CONFIG ###############################
# Hashes are encoded in a special way (much more memory efficient) when they
# have at max a given numer of elements, and the biggest element does not
# exceed a given threshold. You can configure this limits with the following
# configuration directives.
-hash-max-zipmap-entries 64
-hash-max-zipmap-value 512
+hash-max-zipmap-entries 512
+hash-max-zipmap-value 64
+
+# Similarly to hashes, small lists are also encoded in a special way in order
+# to save a lot of space. The special representation is only used when
+# you are under the following limits:
+list-max-ziplist-entries 512
+list-max-ziplist-value 64
+
+# Sets have a special encoding in just one case: when a set is composed
+# of just strings that happens to be integers in radix 10 in the range
+# of 64 bit signed integers.
+# The following configuration setting sets the limit in the size of the
+# set in order to use this special memory saving encoding.
+set-max-intset-entries 512
+
+# Similarly to hashes and lists, sorted sets are also specially encoded in
+# order to save a lot of space. This encoding is only used when the length and
+# elements of a sorted set are below the following limits:
+zset-max-ziplist-entries 128
+zset-max-ziplist-value 64
# Active rehashing uses 1 millisecond every 100 milliseconds of CPU time in
# order to help rehashing the main Redis hash table (the one mapping top-level
projects / redis.git / blobdiff