# the dataset will likely be bigger if you have compressible values or keys.
rdbcompression yes
+# Since verison 5 of RDB a CRC64 checksum is placed at the end of the file.
+# This makes the format more resistant to corruption but there is a performance
+# hit to pay (around 10%) when saving and loading RDB files, so you can disable it
+# for maximum performances.
+#
+# RDB files created with checksum disabled have a checksum of zero that will
+# tell the loading code to skip the check.
+rdbchecksum yes
+
# The filename where to dump the DB
dbfilename dump.rdb
#
slave-serve-stale-data yes
+# You can configure a slave instance to accept writes or not. Writing against
+# a slave instance may be useful to store some ephemeral data (because data
+# written on a slave will be easily deleted after resync with the master) but
+# may also cause problems if clients are writing to it because of a
+# misconfiguration.
+#
+# Since Redis 2.6 by default slaves are read-only.
+#
+# Note: read only slaves are not designed to be exposed to untrusted clients
+# on the internet. It's just a protection layer against misuse of the instance.
+# Still a read only slave exports by default all the administrative commands
+# such as CONFIG, DEBUG, and so forth. To a limited extend you can improve
+# security of read only slaves using 'rename-command' to shadow all the
+# administrative / dangerous commands.
+slave-read-only yes
+
# Slaves send PINGs to server in a predefined interval. It's possible to change
# this interval with the repl_ping_slave_period option. The default value is 10
# seconds.
#
# repl-timeout 60
+# The slave priority is an integer number published by Redis in the INFO output.
+# It is used by Redis Sentinel in order to select a slave to promote into a
+# master if the master is no longer working correctly.
+#
+# A slave with a low priority number is considered better for promotion, so
+# for instance if there are three slaves with priority 10, 100, 25 Sentinel will
+# pick the one wtih priority 10, that is the lowest.
+#
+# However a special priority of 0 marks the slave as not able to perform the
+# role of master, so a slave with priority of 0 will never be selected by
+# Redis Sentinel for promotion.
+#
+# By default the priority is 100.
+slave-priority 100
+
################################## SECURITY ###################################
# Require clients to issue AUTH <PASSWORD> before processing any other
# volatile-lru -> remove the key with an expire set using an LRU algorithm
# allkeys-lru -> remove any key accordingly to the LRU algorithm
# volatile-random -> remove a random key with an expire set
-# allkeys->random -> remove a random key, any key
+# allkeys-random -> remove a random key, any key
# volatile-ttl -> remove the key with the nearest expire time (minor TTL)
# noeviction -> don't expire at all, just return an error on write operations
#
############################## APPEND ONLY MODE ###############################
-# By default Redis asynchronously dumps the dataset on disk. If you can live
-# with the idea that the latest records will be lost if something like a crash
-# happens this is the preferred way to run Redis. If instead you care a lot
-# about your data and don't want to that a single record can get lost you should
-# enable the append only mode: when this mode is enabled Redis will append
-# every write operation received in the file appendonly.aof. This file will
-# be read on startup in order to rebuild the full dataset in memory.
+# By default Redis asynchronously dumps the dataset on disk. This mode is
+# good enough in many applications, but an issue with the Redis process or
+# a power outage may result into a few minutes of writes lost (depending on
+# the configured save points).
#
-# Note that you can have both the async dumps and the append only file if you
-# like (you have to comment the "save" statements above to disable the dumps).
-# Still if append only mode is enabled Redis will load the data from the
-# log file at startup ignoring the dump.rdb file.
+# The Append Only File is an alternative persistence mode that provides
+# much better durability. For instance using the default data fsync policy
+# (see later in the config file) Redis can lose just one second of writes in a
+# dramatic event like a server power outage, or a single write if something
+# wrong with the Redis process itself happens, but the operating system is
+# still running correctly.
#
-# IMPORTANT: Check the BGREWRITEAOF to check how to rewrite the append
-# log file in background when it gets too big.
+# AOF and RDB persistence can be enabled at the same time without problems.
+# If the AOF is enabled on startup Redis will load the AOF, that is the file
+# with the better durability guarantees.
+#
+# Please check http://redis.io/topics/persistence for more information.
appendonly no
#
# no: don't fsync, just let the OS flush the data when it wants. Faster.
# always: fsync after every write to the append only log . Slow, Safest.
-# everysec: fsync only if one second passed since the last fsync. Compromise.
+# everysec: fsync only one time every second. Compromise.
#
# The default is "everysec" that's usually the right compromise between
# speed and data safety. It's up to you to understand if you can relax this to
# or on the contrary, use "always" that's very slow but a bit safer than
# everysec.
#
+# More details please check the following article:
+# http://antirez.com/post/redis-persistence-demystified.html
+#
# If unsure, use "everysec".
# appendfsync always
# There is no limit to this length. Just be aware that it will consume memory.
# You can reclaim memory used by the slow log with SLOWLOG RESET.
-slowlog-max-len 1024
+slowlog-max-len 128
############################### ADVANCED CONFIG ###############################