xnu-4903.241.1.tar.gz

[apple/xnu.git] / osfmk / i386 / postcode.h

/*
 * Copyright (c) 2008 Apple Computer, Inc. All rights reserved.
 *
 * @APPLE_OSREFERENCE_LICENSE_HEADER_START@
 * 
 * This file contains Original Code and/or Modifications of Original Code
 * as defined in and that are subject to the Apple Public Source License
 * Version 2.0 (the 'License'). You may not use this file except in
 * compliance with the License. The rights granted to you under the License
 * may not be used to create, or enable the creation or redistribution of,
 * unlawful or unlicensed copies of an Apple operating system, or to
 * circumvent, violate, or enable the circumvention or violation of, any
 * terms of an Apple operating system software license agreement.
 * 
 * Please obtain a copy of the License at
 * http://www.opensource.apple.com/apsl/ and read it before using this file.
 * 
 * The Original Code and all software distributed under the License are
 * distributed on an 'AS IS' basis, WITHOUT WARRANTY OF ANY KIND, EITHER
 * EXPRESS OR IMPLIED, AND APPLE HEREBY DISCLAIMS ALL SUCH WARRANTIES,
 * INCLUDING WITHOUT LIMITATION, ANY WARRANTIES OF MERCHANTABILITY,
 * FITNESS FOR A PARTICULAR PURPOSE, QUIET ENJOYMENT OR NON-INFRINGEMENT.
 * Please see the License for the specific language governing rights and
 * limitations under the License.
 * 
 * @APPLE_OSREFERENCE_LICENSE_HEADER_END@
 */

#ifndef	_I386_POSTCODE_H_
#define	_I386_POSTCODE_H_

/*
 * Postcodes are no longer enabled by default in the DEBUG kernel
 * because platforms may not have builtin port 0x80 support.
 * To re-enable postcode outpout, uncomment the following define:
 */
//#define DEBUG_POSTCODE 1

/* Define this to delay about 1 sec after posting each code */
//#define POSTCODE_DELAY 1

/* The POSTCODE is port 0x80 */
#define	POSTPORT 0x80

#define	SPINCOUNT	300000000
#define CPU_PAUSE()	rep; nop

#if DEBUG_POSTCODE
/*
 * Macro to output byte value to postcode, destoying register al.
 * Additionally, if POSTCODE_DELAY, spin for about a second.
 */
#if POSTCODE_DELAY
#define POSTCODE_AL			\
        outb    %al,$(POSTPORT);	\
	movl	$(SPINCOUNT), %eax;	\
1:					\
	CPU_PAUSE();			\
	decl	%eax;			\
	jne	1b
#define POSTCODE_AX			\
        outw    %ax,$(POSTPORT);	\
	movl	$(SPINCOUNT), %eax;	\
1:					\
	CPU_PAUSE();			\
	decl	%eax;			\
	jne	1b
#else
#define POSTCODE_AL			\
        outb    %al,$(POSTPORT)
#define POSTCODE_AX			\
        outw    %ax,$(POSTPORT)
#endif /* POSTCODE_DELAY */

#define POSTCODE(XX)			\
	mov	$(XX), %al;		\
	POSTCODE_AL

#define POSTCODE2(XXXX)			\
	mov	$(XXXX), %ax;		\
	POSTCODE_AX

/* Output byte value to postcode, without destoying register eax */ 
#define	POSTCODE_SAVE_EAX(XX)		\
	push	%eax;			\
	POSTCODE(XX);			\
	pop	%eax

/*
 * Display a 32-bit value to the post card - low byte to high byte
 * Entry: value in %ebx
 * Exit: %ebx preserved; %eax destroyed
 */ 
#define POSTCODE32_EBX			\
	roll	$8, %ebx;		\
	movl	%ebx, %eax;		\
	POSTCODE_AL;			\
					\
	roll	$8, %ebx;		\
	movl	%ebx, %eax;		\
	POSTCODE_AL;			\
					\
	roll	$8, %ebx;		\
	movl	%ebx, %eax;		\
	POSTCODE_AL;			\
					\
	roll	$8, %ebx;		\
	movl	%ebx, %eax;		\
	POSTCODE_AL

#else	/* DEBUG_POSTCODE */
#define POSTCODE_AL
#define POSTCODE_AX
#define POSTCODE(X)
#define POSTCODE2(X)
#define POSTCODE_SAVE_EAX(X)
#define POSTCODE32_EBX
#endif	/* DEBUG_POSTCODE */

/*
 * The following postcodes are defined for stages of early startup:
 */

#define	PSTART_ENTRY			0xFF
#define PSTART_REBASE			0xFE
#define PSTART_BEFORE_PAGING		0xFE
#define	PSTART_VSTART			0xFD
#define VSTART_ENTRY			0xFC
#define VSTART_IDT_INIT			0xFB
#define VSTART_IDLE_PTS_INIT		0xFA
#define VSTART_PHYSMAP_INIT		0xF9
#define VSTART_DESC_ALIAS_INIT		0xF8
#define VSTART_SET_CR3			0xF7
#define VSTART_CPU_DESC_INIT		0xF6
#define VSTART_CPU_MODE_INIT		0xF5
#define VSTART_EXIT			0xF4
#define	I386_INIT_ENTRY			0xF3
#define	CPU_INIT_D			0xF2
#define	PE_INIT_PLATFORM_D		0xF1

#define	SLAVE_STARTPROG_ENTRY		0xEF
#define	SLAVE_PSTART			0xEE
#define	I386_INIT_SLAVE			0xED

#define	PANIC_DOUBLE_FAULT		0xDF	/* Double Fault exception */
#define	PANIC_MACHINE_CHECK		0xDC	/* Machine-Check */
#define	MP_KDP_ENTER			0xDB	/* Debugger Begin */
#define	MP_KDP_EXIT			0xDE	/* Debugger End */
#define	PANIC_HLT			0xD1	/* Die an early death */ 
#define	BOOT_TRAP_HLT			0xD0	/* D'oh! even earlier */ 

#define ACPI_WAKE_START_ENTRY		0xCF
#define ACPI_WAKE_PROT_ENTRY		0xCE
#define ACPI_WAKE_PAGED_ENTRY		0xCD

#define CPU_DESC_LOAD_ENTRY		0xBF
#define CPU_DESC_LOAD_GS_BASE		0xBE
#define CPU_DESC_LOAD_KERNEL_GS_BASE	0xBD
#define CPU_DESC_LOAD_GDT		0xBC
#define CPU_DESC_LOAD_IDT		0xBB
#define CPU_DESC_LOAD_LDT		0xBA
#define CPU_DESC_LOAD_TSS		0xB9
#define CPU_DESC_LOAD_EXIT		0xB7

#ifndef ASSEMBLER
inline static void
_postcode_delay(uint32_t	spincount)
{
	asm volatile("1:			\n\t"
	             "  rep; nop;		\n\t"	
		     "  decl %%eax;		\n\t"
		     "  jne 1b"
		     : : "a" (spincount));
}
inline static void
_postcode(uint8_t	xx)
{
	asm volatile("outb %0, %1" : : "a" (xx), "N" (POSTPORT));
}
inline static void
_postcode2(uint16_t	xxxx)
{
	asm volatile("outw %0, %1" : : "a" (xxxx), "N" (POSTPORT));
}
#if	DEBUG_POSTCODE
inline static void
postcode(uint8_t	xx)
{
	_postcode(xx);
#if	POSTCODE_DELAY
	_postcode_delay(SPINCOUNT);
#endif
}
inline static void
postcode2(uint8_t	xxxx)
{
	_postcode2(xxxx);
#if	POSTCODE_DELAY
	_postcode_delay(SPINCOUNT);
#endif
}
#else
#define postcode(xx) do {} while(0)
#define postcode2(xxxx) do {} while(0)
#endif
#endif

#endif /* _I386_POSTCODE_H_ */